Combustor Articles & Analysis
-
Application of reactor net models for the simulation of gas-turbine combustor emissions
The work deals with the evaluation of applicability of reactor net models and different reaction mechanisms for the predictions of emission characteristics of aero-engine combustors operating both in diffusion and in homogeneous burning modes. It is shown that the accuracy of the calculations of emission indices for NO x , CO and unburned hydrocarbons (UHC) is dependent strongly on the applied ...
-
Ghost Series AB 200 x 20` Enclosed Combustors - Case Study # 170102
Project Details Location: Mid-Continent Heat Capacity: 18.4 MM BTU/hr Inlet Pressure (AP): 2 psig Aereon's Ghost Series enclosed combustors are designed to burn waste gas in a smokeless application. This customer in the Mid-Continent region is using 6 combustors as an emergency backup to the sales line. Waste gas is supplied through a manifold system. The small footprint and simple ...
-
Ghost Series AB20 EPA Certified Enclosed Combustor - Case Study #170603
PROJECT DETAILS Location: Texas Panhandle Max inlet flow rate at 1,600 Btu/ft3 AB-20: 36.0 MSCFD Rated heat capacity: 2.4 MMBTU/hr Inlet Temperature: < 130 °F Minimum Pressure required for operation: 4 oz/in2 Smokeless flow rate: 0 -100% of design flowrate meets Ringelmann1 Destruction Rate Efficiency: 98% DRE Aereon’s Ghost Series AB20 Enclosed Combustor is used in this ...
-
Exergetic performance of a cylindrical methane–air microcombustor under various inlet conditions
The entropy generation analysis is performed on a methane–air cylindrical microcombustor. The combustor is studied under different fuel–air equivalence ratios and two different inlet velocities. The results reveal that entropy generation due to heat transfer has the highest contribution to the total exergy destruction. Besides, the chemical and mixing entropy generations have the next greatest ...
-
Ghost Series AB-20 x 20’ Enclosed Combustor - Case Study #170205
PROJECT DETAILS Location: Permian Basin Flow Rate LP: 20.0 MSCFD LP Inlet Pressure (ΔP): 4 oz/in.2 Smokeless %: 100% Pilot & Controls: ProFire2100 Solar Package: No Electricity Required Installed Year: 2017 Aereon’sGhost Series Enclosed Combustor (EPA Certified for Quad O Compliance) is used to burn off waste natural gas from a low pressure tank. The technology used ...
-
Influence of bed height on the quality of rice husk ash in a fluidised bed combustor
The purpose of this study was to investigate the effect of bed height on the quality of rice husk ash in a 210–mm diameter pilot scale fluidised bed combustor. The degree of rice husk burning in the fluidised bed could be deduced from the temperature of the combustor and the particle size of the resulting ash. The turbulence in the bed would break down the char skeleton of the rice husk ...
-
A cost–effective backward Lagrangian method for simulation of pollutant formation in gas turbine combustors by post–processing of complex 3D calculations
A backward Lagrangian Monte Carlo modelling is proposed to calculate by post–processing the PDF of the thermo–chemical parameters of complex turbulent reactive flows simulated with a simple turbulent combustion model. PDF's of minor species such as pollutant species (NOx, soot, unburnt hydrocarbons...) can be easily obtained as long as these species have no significant influence on the main ...
-
HP1500/HP3000 Flares - Case Study #170101
Project Details Location: Pecos, TX Flow Rate : 5 MMscfd Inlet Pressure(ΔP): 20psi Aereon’s HP series flares are used to burn high pressure waste gas at multiple flow rates. Customer used multiple flares along with a combustor to be able to accommodate high and low pressures coming from multiple sources. The integral skid design reduces installation costs and has a minimal ...
-
Exergetic and exergo–economic analysis of a turboprop engine: a case study for CT7–9C
The turboprop engine has played an important role in short haul commuter and military transport aircraft where high speed is not critical. It may provide the aviation sector with one of the most significant means of achieving reduced operating costs through reductions in fuel consumption. This paper deals with exergo–economic analysis of a modern turboprop engine (CT7–9C) with a free power ...
-
So, What’s all this fuss about EPA Certified Combustors: should you care?
In the US market, there are over 20 companies aggressively marketing “Combustors” for the US Upstream market with various claims about performance, EPA NSPS 0000a “Compliant” designs and/or EPA NSPS 0000a “Certified” designs. With all of the mixed messages, what do you really need to know, and what do you need to consider so that you don’t ...
-
Detailed chemical modelling of a flameless combustion turbine for pollution prevention
Flameless combustion has been acknowledged as one of the most interesting combustion technologies to meet both the targets of high process efficiency and low pollutant emissions. The present investigation is concerned with the application of the flameless combustion mode to an adiabatic combustor, typically used in gas turbine engines. Detailed chemical kinetics calculations, by means of a ...
-
Ghost Series Enclosed Combustor AB-200 - Case Study #170403
PROJECT DETAILS Location: RockyMountains FlowRate: 1.75MMSCFD InletPressure: 9”WC Heating Value: 227 BTU/SCF Application: Coal Mine Methane Recovery Aereon’s GHOST Series Enclosed Combustor AB-200 was purchased by the client to recover methane from an abandoned coal mine in order to earn hydrocarbon credits. Prior to incinerating the gas, methane was simply venting to the ...
-
Ghost Series & Momentum Series Combo AB-20 Combustor / HP-1500 Flare - Case Study #170203
Project Details Location: Permian Basin Flow Rate HP: 1.5 MMSCFD HP Inlet Pressure (ΔP): 50-75 PSIG Flow Rate LP: 20.0 MSCFD LP Inlet Pressure (ΔP): 4 oz/in.2 Smokeless %: 100% Pilot & Controls: ProFire 2100 & 1300 Solar Package: No Electricity Required Installed Year: 2017Installed Year: 2017 Aereon’s Ghost/Momentum Combo Package (EPA Certified for Quad O ...
-
NOx formation by steam injection using detailed chemical kinetics
In order to improve thermal efficiency of gas turbine system and better control NOx emission, the injection of steam into a gas turbine combustor has been employed. This study has used both chemical equilibrium calculations and the counterflow diffusion flame calculations of methane-air flame aiming at the elucidation of the NOx reduction mechanism due to the steam injection. The influence of the ...
-
Energy and exergy analysis of a gas turbine power plant in Algeria
An exergy analysis of a twin ABB GT13E2 Gas Turbines (GTs) power plant (2 ? 146.2 MW) is presented in this paper. This plant is running since 2004 at F'Krina in the northeastern part of Algeria. The analysis was performed by the flow-sheet programme, 'Cycle-Tempo'. At off-design load (83%), the plant and its apparatus conserve nearly the same design load performances. However, the performance of ...
-
Hydrogen production by catalytic methane decomposition and catalyst regeneration by oxygen mixtures in fluidised and fixed bed reactors
In the present paper, the Thermo-Catalytic Decomposition (TCD) of methane has been investigated in a laboratory-scale bubbling fluidised bed reactor using copper dispersed on γ-alumina as a catalyst. The usefulness of a fluidised bed operation instead of a fixed bed operation has been assessed in terms of methane-to-hydrogen conversion and the amount of carbon accumulated on the catalyst. The ...
-
COMPARISON OF PROCESS FLOWS: FLUID BED COMBUSTOR AND GLASSPACK®
PURPOSEThe purpose of this document is to present the assumptions and calculations used to prepare Minergy Drawing 100-0204-PP00 (attached). The volumetric flows for both a fluid bed combustor (FBC) and Minergy’s patented GlassPack® closed loop oxygen enhanced combustion process are compared on this drawing. In this drawing, process flows are illustrated by scaling the width of the flow arrows in ...
-
COMPARISON OF PROCESS FLOWS: FLUID BED COMBUSTOR AND GLASSPACK® (metric version)
PURPOSEThe purpose of this document is to present the assumptions and calculations used to prepare Minergy Drawing 100-0204-PP00 (attached). The volumetric flows for both a fluid bed combustor (FBC) and Minergy’s patented GlassPack® closed loop oxygen enhanced combustion process are compared on this drawing. In this drawing, process flows are illustrated by scaling the width of the flow arrows in ...
-
Project - Texas Utility Plant - Cogeneration
Capacity: 450 mm BTU A Texas Utility Plant owns and operates eight (8) GE Frame 7B/FA combustion turbines at its generation plant located in Houston, Texas. All eight of the turbines operate normally in combined cycle mode and are utilized for onsite generation of steam and electricity. All eight turbines combust pipeline natural gas exclusively. All eight units are affected by the Clear Air ...
-
5MWe Combined Heat and Power Punt - Veterans Administration Hospital - Case Study
DEVELOPER/OWNER Sempra Energy LOCATION La Jolla, California, U.S.A. PRODUCT Mercury 50 Recuperated Gas Turbine CUSTOMER VALUE Efficient and Stable Power Under the United States Federal Energy Managers Program, the Veterans Administration (VA) Medical Center entered into an energy savings performance contract with Sempra Energy Services. The project required replacing two existing 1.2 MWe ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you