Energy Monitoring Equipment Supplied In Kuwait

The BEAM 3.0 perform in 24/7 production process worldwide with utmost reliability. Even under the most challenging environments BEAM 3.0 guarantee frictionless industrial use for different applications (example: 3D Laser Printer / 3D Laser melting). The Generator produces a continuous flow of Nitrogen with Laser Grade. The BEAM 3.0 has been developed to meet specific requirements in term of gas, ...

Power supply for two 2 wire sensors or transmitters. The power supply has two galvanically isolated outputs for supplying voltage to sensors and transmitters. A built-in communication resistance enables bidirectional HART® communication with SMART sensors and ...

Power supply for one 4 wire sensor or transmitter. The power supply has one output for supplying voltage to 4 wire sensors and transmitters. Connection to mono-phased a.c. networks or to two phase conductors of three-phase supply networks (TN-, TT- or IT-networks as per VDE 0100 T 300/IEC 364-3) with 100-240 V AC nominal voltage ...

Universal flow and energy computer for gases, liquids and steam. The flow and energy manager RMC621 calculates standard volume as well as mass and energy flows of natural and technical gases, fluids and steam from flow, pressure, temperature and density. Depending on the medium calculation of the energy values occurs according to international standards (IAPWSIF97, SGERG88), real gas equations ...

Paperless recording, visualization and monitoring of the process values at the same time. Safe and complete recording and visualization of all process sequences. The Memograph M RSG40 has a wide range of functionality, modular construction and a intuitive operator concept. With its brilliant 7” TFT display it is possible to display process values e.g. as curves, as a circular chart display ...

One or two-channel barrier for the safe separation of 4...20 mA standard signal circuits. The RB223 passive barrier can be used to galvanically isolate active signal circuits (0 to 20 mA) in three applications: Transmission from non-Ex to Ex areas e.g for active adjusters, controllers or indicators, Transmission from Ex to non-Ex areas for connection of active, intrinsically safe circuits to the ...

The BTU meter RH33 is used in applications with liquid energy carriers. It calculates the thermal energy of water acc. to EN1434, glycol/water mixtures or other fluids such as thermal oils. Temperature sensor matching using calibrated temperature sensors is done in the device. Potential for cost savings can be shown by using the software available as an accessory. The device has a custody ...

The Pit Flare (or “Burn Pit”) is usually constructed of an excavation lined with a non-combustible lining of rock or refractory material. Often coupled with a pit liner, our pit flares can be a cost-effective combustion option for an environmentally conscious user. Our high efficiency burner produces a mixture of vapor and liquid from a single source. While most often designed to ...

The IQT Battery Backup actuator provides valve fail-safe operation by utilising power from a battery source during AC supply mains failure. Under normal supply conditions the actuator operates from the site AC electrical supply. On loss of this supply the actuator automatically switches over to receive power from a 24 VDC supply allowing control of the valve to the pre-configured ...

Utility flares (DU series) are one of the most common flare designs use for applications with no smokeless burning requirements. They are also utilized in applications where smokeless flaring can be achieved without the use of an additional assist ...

The PreMix 2000 analyzer accurately and continuously measures the proportions of oxygen (O2) and fuel in premix gases, operating in either excess fuel or excess air conditions. It has the capability to measure the air/fuel ratio in open-flame applications where flue gas measurements are not practical, with measurement and display options including excess O2, excess fuel, oxides/fuel ratio and ...

We design Enclosed ground flares when waste gases are requested to be flared in an enclosed stack, with reduced flame visibility, minimal heat and noise, emissions sampling, ease, and smokeless combustion, in sensitive areas. The stack is internally refractory lined, designed for low and medium flows, has high destruction efficiencies relative to an open flare and designed as natural draft or ...

The Model 100 Continuum Ignitor utilizes a high voltage electric arc to ignite a combustible air/gas mixture. This arc typically occurs every 20 seconds for a two second duration (timing is adjustable). The Continuum provides a spark inside a ‘slipstream’ chamber that diverts a portion of the waste gas to create a combustible air/gas mixture. This allows the Continuum ignitor to ...

Our Titan Demountable Flares, also named demountable derricks, are derrick-supported flares with three, or four leg configurations and overall heights of up to 200 meters. Designed to accommodate several risers/tips on the same derrick structure. Each flare tip has its own set of pilots. The demountable system allows maintenance at grade on each flare tip while keeping the other flare systems in ...

The Sentinel flame monitor reliably provides remote flame detection up to 550 feet away, durability, ease of maintenance and rapid response time. If the monitor detects the absence of a flame for an adjustable amount of time, a set of dry form C contacts are activated and the pilot re-ignition system is set into motion. Response times are markedly quicker than those of a standard thermocouple ...

To dispose of heavy waste gases, which have a greater tendency to smoke, in a smokeless manner, we provide three different design options, depending on customer requirements. Air Assisted Flares, which utilize forced air from blower(s) to provide assist air for combustion and promotes additional air entrain from the ambient due to the relatively high exit speed of the streams. Steam Assisted ...

The Ghost series of enclosed biogas flares is a simple and cost effective combustion solution for a variety of applications where a hidden flame is required. The superior design, high quality stainless steel construction and unmatched versatility make the Ghost Series Enclosed Flares an exceptional choice for emissions control within the biogas and wastewater industries. Additionally, each ...

GeoSIG's SMS/SAS systems are mostly used in Nuclear Power Plant or other Industrial Facility Seismic Monitoring Projects. If you need any further specific information, please do not hesitate to contact us through our agent assigned for this kind of instrumentation for your geographical region or ...

Our Peacock Oil Burners are designed to flare liquid hydrocarbons without liquid fallout or soot formation. These burners provide excellent service for well testing operations. When only oil is flared, a high-pressure air or gas source is required to provide additional mechanical atomization to ensure the mixture is a fine mist when it exits the burner nozzle which is designed to accept separate ...

AEREON's halogenated thermal oxidizer systems are designed to handle hazardous halogenated streams produced from various chemical processes in a safe and effective manner. Systems are designed to maintain high destruction efficiency of the compounds with an effective high chamber temperature and residence ...