Power Distribution Equipment & Supplies In Latin America

Mounting bracket for carrying rail 35/7,5. Place the mounting plate on the backside of the enclosure with the springloaded clamp facing downwards. Fasten the mounting plate using the four attached screws ø4.8x13, see figure 1 location ...

The KOLLER Offshore Wireline Unit has been designed for measurements and workover activities with wire capacities above 7,650 m / 25,000 ft. It is suitable for both offshore and onshore applications. The 131 HP guarantees maximum pull force and speed at any depth, even with heavy tools. One of the new features of the power pack is a maintenance free flame trap together with a fault analytic ...

This Honda powered gas power packis ideal for driving our 3" trash pumpand even our 6" high-volume propeller pump. It also can provide hydraulicpower to run many other hydraulic tools now availableusing the variable speed throttle to control ...

Reverse Camera/Monitor Systems, from Federal Signal, provide the driver with an expanded field-of-view for enhanced safety during back-up or while maneuvering the vehicle in challenging environments. With a variety of cameras, monitors, and mounting options available, Reverse Camera/Monitor Systems has a solution for almost any vehicular application. ...

A cell contacting unit CVP (Cell Voltage Pickup) is a multichannel potential tap for detecting cell voltages on batteries or fuel cell stacks. Depending on the stack used, different construction principles are employed. The CVP pictured here is just one ...

This portable and rugged diesel power pack is ideal for driving our 3" trash pumps and even our 6" high-volume propeller pump. It also can provide hydraulic power to run many other hydraulic tools using the variable speed throttle to control hydraulic ...

The CVM systems with MASTER feature comprehensive functionalities and high-speed data transmission and processing. A complete system consists of the number of CVM G5 measuring modules required for the respective application, a bus module, a termination module and a process module. Adding the process modules Master or SlimMASTER to the measurement module stack enables more comprehensive as well as ...

The digital I/O module has individually configurable inputs and outputs. The outputs can be used as high-side, low-side or push / pull drivers. Due to the high voltage ranges, the module is also suitable for special applications in the automotive environment. The module is optimally equipped for use in harsh environments. Application areas are, among others, test stands, HIL systems and ...

The HT5E power unit is driven by a 10HP electric motor for use where electric power is available. It is designed to drive several of our pump models including the S3T, S3TC and S6P. Other hydraulic tools and equipment may also operate from this power ...

The MCM-U08 AII module is ideal for measuring unipolar voltages in test benches and test systems. Use the module to monitor the voltage of the fuel cell, battery stacks, lithium-based batteries and electrolyzers. It is optimally equipped for use in harsh environments. Application areas include starter test benches, engine test stands, generators test stands, HIL systems and test benches for ...

Applications: To transfer fluids at flow rates between 10 and 175 GPM up to 150 psi in applications such as fleet, aviation, marina, construction, and agriculture refueling as a well as bulk loading/unloading for rail, truck, and marine vessels. Typical fluids include Fuels, Oils, Lubes, Anti-freeze, Petroleum Contact Water (PCW), Transmission Fluid, and some petrochemicals. The Tri-Lobe pump ...

The IMR 550P device is for the cleaning of gases and is suitable for use in conjunction with all gas measuring and analysis instruments. It is encased in a handy portable case. It is especially designed for use with the IMR 1400 and IMR 2800 series or any other type of combustion gas analyzer. The gas is filtered by the 3 micron filter and then heated by the sampling hose. The unique ...

The HT74DJV features a John Deere 4 cylinder water cooled diesel with your choice of fixed displacement gear of pressure compensated piston hydraulic pumps. It is designed to drive our submersible pumps or other hydraulic equipment requiring flows to 40 GPM and pressures to 2500 ...

The VPInstruments 3 Phase Power Meter is the highly accurate power meter for your permanent power measurements. With the power meter you can measure the voltage and current of all three phases. Get the complete picture as the sensor provides power, voltage, current, cos(phi) and many more electrical parameters. Via the RS485 (Modbus RTU) interface you can connect the 3 Phase Power Meter to any ...

The HT20DYS power unit is driven by a Yanmar Diesel engine and is designed to drive several of our pump models including the S3TDI, S4T, S3CSL, and S6P. A built-in fuel tank allows this unit to run up to 12 hours between refills. Other hydraulic tools and equipment may also operate from this power ...

This is a 3/4″ diameter, compact swaged cable by 100 feet long. The end is terminated with a Crosby Open Socket for pulling TRIC products such as the 4″ Quick Lock Head Assembly (TTA-QLHA-4ASM), and he other end of the cable is brazed for use with the 2″ and 3″ Triple-Chuck Heads (TTA-TCHEAD-3ASM). This cable can be pulled with 3/4″ Monolithic Grippers ...

For the commissioning and testing of cell voltage measurement electronics and FuelCell control units, and in particular for the software testing of such ECUs, it is necessary to simulate cell-specific voltage values. The simulation modules of the MCM IntelliSim series, in conjunction with a master module enable active simulation of a fuel cell stack without the need to integrate a real stack into ...

This power unit features a 22 HP Honda OHV gas engine, extended run fuel tank, extra oil cooling and easy handling. It is available with a fixed displacement gear pump or pressure compensated piston pump. Great for continuous duty applications powering our pumps or other hydraulic tools and equipment. Variable speed throttle controls hydraulic ...

The MEL-1000 is a control and control centre for electric boilers. Mel-1000 comes with test report from quality ...

Cell sensing: Single Cell SC (1C). Contact design: 0.5 mm spring wire with S-shape. Contact bearing: In PCB on one side with redundant contact pin. Locking type: Friction lock in pinhole, additional hold-down possible. Contact pitch min.: 0.950 mm. Pinhole/ Geometry: Pin shape punched in bipolar plate foil. Bipolar plate material: Metal. Connection type: Flexcard. Benefit (USP): Smallest cell ...