Energy Equipment & Supplies In Belize

Deep Cycle Battery with Cover, 24 Volt, 408 Ah (at 20 hr.). Some 24 Volt batteries do not come with a cover, the image is for illustration purposes ...

Pulling force: 51 tons @ 4,000 psi. Piston area: 25.13 square inches. Hydraulic flow rate: 10 to 30 GPM. Cable size: 3/4″, 7/8″. Puller weight: 138 pounds. 12” pulley base: 131 pounds (15” L x 14” W x 19” H). 24” x 1” steel resistance plate: 50 pounds. Pipe materials, routes, and ground conditions vary greatly. Please consult TRIC technical support ...

The Inciner8 Autoloader is a British steel product made of the highest-grade steels and manufactured by our Queens Award Team, recognised for their innovation and manufacturing ...

The Sirocco is our smallest and most portable waste incinerator and has been designed to be easy to relocate and use almost anywhere. Requiring just a small amount of electricity to power the fan - no other fuel source is required. The efficient process reduces waste to as little as 3% of its initial volume. It uses cyclonic air technology by using the high-pressure fan to pull air into the main ...

With the function tester for ABS control units, individual function modules of the control unit hardware can be tested. For this purpose, various simulation and measurement technology components from the MCM product family are installed in the test system. Special loads can be connected via an additional load connector. If the built-in measurement and stimulation channels are insufficient, ...

They supply the highest differential pressures or pressure ratios in the AERZEN product portfolio – the oil flooded compressor series VMY. VMY compressors are the ideal solution for low molar weights, coolants, and generally for fluctuating operation conditions and gas ...

The i8-500G has the third largest capacity in our range of general waste incinerators. Suitable for various waste streams such as wood, paper, cardboard and plastics. The i8-500 uses groundbreaking design and user features found on our much larger machines. The i8-500 took over two years to develop and was designed from the ground up to offer impressive burn rates and large batch sizes. The ...

The gas dome or gas cover is used first and foremost as the basis for various attachments for digesters, i.e., foam traps, gas extraction units, safety devices, mixers, measurement units etc., and secondly as an access point into the digester. For both applications the gas dome should be adequately dimensioned in order to meet all requirements. ennox gas domes comprise of a base unit with a ...

Simple operation and fully automated operation of up to four hot water or heating boilers (master/slave). Compact "plug and play" control with innovative connectivity. - Modular complete solution with cost advantage, for all single-flame-tube hot water and heating boilers - Intelligent sequence control for up to four boilers - Intuitive operation via colour touch display and function keys for ...

Texas Boom offers the Leeagra DOT 500 Diesel Fuel Trailer. This trailer is built to be safe because it’s strong. Offering 500 gallon storage and transport of class 3 combustible materials. With all the features highlighted below, the DOT 500 is in a class by itself to meet your fuel hauling ...

A biogas holder is generally a floating cover with an extended rim that is submerged into the water level adequately so as to ensure that in the maximum lift position of the floating cover the rim still remains below the top water level. The covers for gas holders are designed with a vertical guided system. The rollers are attached with the cover of gas holder around its peripheral. This ensures ...

Cell sensing: Single Cell SC (1C). Contact design: 0.5 mm spring wire with S-shape. Contact bearing: In PCB on one side with redundant contact pin. Locking type: Friction lock in pinhole, additional hold-down possible. Contact pitch min.: 0.950 mm. Pinhole/ Geometry: Pin shape punched in bipolar plate foil. Bipolar plate material: Metal. Connection type: Flexcard. Benefit (USP): Smallest cell ...

The model CEJS High Voltage Electrode Steam Boiler is the proven leader with more hours of operating experience over a wide range of applications than any competitor. The CEJS electrodes are vertically mounted around the inside of the pressure vessel which enables the CEJS to produce maximum amounts of steam in a minimum amount of floor ...

Tube–tube heat exchanger (TTHE) is a low cost, vented double wall heat exchanger which increases reliability by avoiding mixing of fluids exchanging heat. They are manufactured as a fully-welded design, with removable end caps and insulated if ...

- For recovering heat from flash steam from thermal water treatment - Heat recovery and thus efficiency improvement - Energy produced can be used for additional heating or for transfer to a separate water circuit Highly efficient boiler systems with perfectly matched boiler house components ensure that low levels of energy consumption and emissions are ...

The highly efficient UT-M is a three-pass boiler designed for 750 to 19,200 kW of heating at up to 16 bar. Its various output sizes and temperature ranges up to 190 °C enable flexible operation for countless process heat and heating ...

It is suitable for disposing of horses, cattle and other large or bulky agricultural waste streams. This system benefits from a wide opening door and high hourly burn rates which makes it a preferred disposal solution for farms, shooting practices, slaughterhouses, abattoirs, veterinary practices or similar facilities with high quantities of agricultural waste. One of our newest designs is the ...

The i8-75A is a medium capacity animal incinerator from our range of 'DEFRA Approved' models and is suitable for disposing of game, deer, poultry, sheep and the largest breeds of domestic animals with dual function as a pet cremation system. Using the same successful format as the i8-55A the i8-75A increases the capacity of the primary chamber allowing for greater burn rates and the capacity to ...

The KOLLER Spooling Unit serves to spool slickline or wireline from a transport drum onto a winch drum. It's a skid-mounted design with electro/hydraulic ...

The Polychem Torque Limiter is an easy-to-reset alternative to traditional shear pin devices. It provides reliable overtorque protection by transmitting torque through balls retained in detents against adjustable spring pressure. When torque exceeds a preset value, the balls leave their seats and roll free to completely disengagem the driving and driven components, preventing costly drive system ...