Cooling Tower Equipment & Supplies

Hence, much more power can be generated from the same steam flow when compared with non-condensing plants. After leaving the turbine the steam encounters cooling water sprays in a direct contact condenser. The heat gained by the cooling water in the condensing process is typically released to atmosphere in a cooling tower. Gases ...

Air cooled Heat Exchanger (or) Fin fan Cooler or Air Fin Cooler are the same Air Cooling equipment. In some part of the world Air Cooled Heat Exchangers are also known as Air Fin Cooler. Simply says Air Fin cooler, Fin Fan cooler, Coil Cooler, Dry Cooling Tower are the other names of Air Cooled ...

The plate heat exchanger is made of 2 frames and a number of plates that depend on the volume to be exchanged. The plates have characteristic ridges that are necessary to create flow channels through which the fluid moves in perfectly opposing currents,minimizing the required surface area for an optimal heat exchanger. The frames are made of two pained carbon steels slabs. The internal plates ...

RYDLYME Biodegradable Descaler is used to safely and efficiently dissolve tough mineral deposits such as water scale, limescale, calcium, and rust from the water side of industrial equipment! Recommended by the U.S. Navy and countless OEMs, RYDLYME descaling chemical is NSF-registered for use in various industries and applications including beverage, pharmaceutical, bottling, and food processing ...

Public systems include cooling towers, air compressors, pyrolysis oil storage tanks, waste heat recovery systems, waste water treatment equipment, waste gas treatment systems, etc. The public systems have different designs depending on the location of the installation, and the waste heat recovery device of the system can also use waste heat. ...

Other technical features of these machines are the use of modulating burners with low emissions, the remote or incorporated air/water cooling tower, the lack of vibrations, the water system pump is on board and there is the possibility of the functional control via modem. The installation of such equipments can be done either outdoor or in a thermal ...

Waste heat from thermal separation and other industrial processes is often released unused into the environment through cooling towers or condensers. At the same time, there is an extremely high demand for process steam. PILLER has the solution: The PILLER Industrial Heat Pump which enables users to recover surplus heat and to supply steam. The PILLER Industrial ...

TransPacific Energy (TPE) is a high-tech corporation that designs, builds, owns, operates, sells and installs proprietary, modular Organic Rankine Cycle (“ORC”) utilizing multiple refrigerant mixtures to maximize heat recovery and convert waste heat directly (75F to 950F) from industrial processes, solar and geothermal, biomass converting it into electrical energy. TPE technology can also be ...

The HPX water source series single packaged unit consists of a high efficiency compressor, air to refrigerant evaporator coil, water to refrigerant condenser coil, expansion valve, reversing valve, centrifugal blower, high efficiency motor, and a control panel with all necessary protection devices and safety circuit. Units are designed to operate with an entering water temperature between 500F ...

Ormat offers GCCU modules in a wide range of sizes in order to accurately match the power plant to the geothermal energy resource. The result is significant savings in well drilling and resource development. The GCCU can be air-cooled so that all steam condensate can be 100% re-injected. Total fluid re-injection sustains reservoir life and provides pressure support. Due to the ...

They are also employed in industrial production processes, for instance, in the air conditioning of buildings where they cool or re-cool liquids. Closed cooling circuits using finned tube heat exchangers are favored over open water circuits due to issues such as Legionella, high fresh water consumption, and the complex water treatment required by ...

The Active Cooler Organic Rankine Cycle (ORC) process converts fluid heat sources - such as engine jacket water and low temperature geothermal - into clean electricity. In the process the excess heat is utilized rather than wasted, generating power while reducing the cooling load up to 100%. This allows the ORC system to prioritize cooling and the production of ...

FEATURES OF REXNORD ADDAX CARBON FIBRE DRIVE SHAFT  LOW WEIGHT- INCREASED BEARING LIFE, EASY INSTALLATION & MAINTENANCE (25% LESS WEIGHT THAN STEEL SPACER).  CORROSION RESISTANT- EXTENDED SERVICE LIFE. ECONOMICAL.  LOW COEFF. OF THERMAL EXPANSION- REDUCE STRESS & VIBRATION.  UNIFIED FLEX ELIMENT- LOW MAINTENANCE COST.  HIGH MIS-ALIGNMENT CAPACITY- EASY TO INSTALL & REDUCE OWNERSHIP COST. ...

Pure Air Solutions supplies fully integrated air cooling systems, complete with adiabatic water cooling towers or closed loop water/glycol systems. Our line of Calorplast plastic heat exchangers is most suited for process air cooling under condensing conditions. Condensed water flows freely since the small plastic tubes have no ...

As gearbox manufacturers, we excel in manufacturing a wide range of customised and tailor-made industrial gearboxes and drives. With our customised gearboxes, we are able to satisfy power transmission needs in selected industries. Our major strength includes the ability to customise an existing standard product into a new design to meet industry standard requirements. Our qualified engineers ...

Ceramic Pall ring is the advanced products of ceramic Raschig ring. Compared with ceramic Raschig ring, there are two layers of window on the cylinder wall. And each layer has five ligules bending inward. It has single layer pall ring and double layer pall ...

Variable frequency speed control: according to the change of a parameter of the system (such as inlet and outlet water temperature), the fan operation is stepless regulated by the frequency converter, in order to achieve the purpose of energy ...

The process of purifying CO2 is obtained from burning of fuel, using MEA (Monoethanolamin) in a aqueous solution which has been known for quite some time. The plant uses a modernized process by which high purity and food quality CO2 can be obtained. The plant has the latest automatic control equipment and is easy to operate and requires very little maintenance. The CO2 containing combusion gases ...

Tube Heat Exchanger is a class of heat exchanger designs used in all processes. It has several variations within its own ...

METALCLAD CeramAlloy CP+ is a two component, 100% solids, high-performance polymer composite specifically formulated to provide effective repair and rebuilding characteristics on all types of fluid flow equipment. METALCLAD CeramAlloy CP+ is a paste when mixed, so it is easily applied. When cured, however, CP+ becomes a metal-hard, ceramic-like ...