Gas Cooling Equipment Supplied In USA

The water-saturated raw gas enters the piping system where it is cooled in a dryer. A separator then eliminates the liquid faction of the biogas, after which the gas is reheated through a blower and the pressure is boosted. ...

State-of-the-art Evaporative Gas Cooling and Conditioning Systems. Available Features: Downflow/upflow spray cooling tower design. Dual-fluid compressed air systems. Single-fluid mechanical atomization systems. Hybrid low-pressure assisted single fluid ...

We’re focused on Gen-IV High-Temperature Gas-cooled Reactors (HTGR) as the technology of choice, with advantages in sustainability, economics, reliability and ...

Amerair has a complete line of direct contact heat exchangers that are designed to recover heat from process waste gases and transfer this valuable heat to process slurries or plant water heating systems. Amerair’s direct contact heat exchangers can be applied to hot process emission controls systems utilizing any type of particulate control device. Process water or slurries, having solids ...

Fog cooling system basically consists of fog nozzles installed on stainless steel arrays typically placed across the section of the gas turbine inlet air ducting before or after the air filter; high-pressure stainless steel head pumps supply water from 1000 to 3000 psi (70-200 bar); pre-filter unit at pump water inlet to block big particles (bigger than 1 micron) ...

Heat exchangers used for compressed gas are used for cooling. Our heavy wall tubes can stand working pressures of 5,200 psi. Tube sizes range from 3/8 inch to 5/8 inch. Materials include copper, aluminum, stainless steel, carbon steel, titanium and others. This product is brazed or welded depending on the material and ...

Simple cycle output (ISO), 593 MW(e), Combined cycle efficiency: > 64%, Derived from proven H-class technology. The next generation of advanced air-cooled gas turbines. Our HL-class gas turbines are paving the way to the next level of efficiency and performance. Derived from proven H-class technology in an evolutionary development step, the ...

Built at our facility, these well-designed units are a great fit with our Limited Access Drill Rigs. Hydraulic Equipped with an air cooled Koehler gas engine, this unit outputs 3000 psi at 25 ...

GE’s 9HA high efficiency, air-cooled gas turbine is one of the industry leaders among H-class offerings, and now the 9HA gas turbine is at the heart of the world's most efficient combined-cycle power ...

The Active Cooler acts as a net-zero cooling to power solution, meeting the cooling system's requirements while generating clean electricity as a secondary function when the cooling load is not at peak demand. The Active Cooler (AC800) cools up to 800 kWth and can generate up to 75 kWe. ...

TheBioMax systems arefully automated, using software to precisely control material flow, gasification, gas cooling and filtration to produce extremely clean ...

Fisher Energy offers standard and custom designed systems to meet the requirements of each application, including fine filtration, coalescing filtration, pressure regulation, process heating (electric or gas-fired), cooling, J-T gas conditioning, and sour gas treatment. These systems include all required instrumentation and ...

World's Largest, Most Efficient Heavy-Duty Gas Turbine in Its Class. The 9HA high-efficiency, air-cooled gas turbine leads the industry. Its flexible conversion of fuel to electricity helps you meet increasingly dynamic power demands cost effectively. Achieves greater than 61 percent net combined-cycle efficiency. ...

Thermal Engineering’s Industrial Products Division designs and manufactures centrifugal compressor intercoolers and aftercoolers. These units cool gas between and in the following stages of compression and often provide plant air, as ...

GE introduced the H-class combined-cycle power plant more than a decade ago, and was the first in the industry to reach more than 200,000 hours of H-class operation. The air-cooled HA gas turbines in GE’s current plant offerings simplify construction, operation, and maintenance. Our industry-leading efficiency and output result in the lowest cost ...

LNG is a natural gas (methane) that is cooled, through a cryogenic process to a liquid state for ease, efficiency and safety of onsite storage or transportation via truck, train, or marine vessel. It is particularly beneficial as a clean burning fuel for reaching remote areas that lack direct pipeline infrastructure. ...

Water, oil, and other contaminants cause corrosion in critical areas of electric power generators, resulting in diminished efficiency and increasing the likelihood of forced outages. Increased dew point levels also detract from generator efficiency by increasing windage losses. E/One's Generator Gas Dryer (GGD II) is a dual-chamber system that continuously dries and recirculates ...

Heat is recovered indirectly from the incinerator exhaust gases by passing them through a gas tube heat exchanger. Cool ambient air is blown across the hot heat exchanger tubes, which provides heated clean air for factory space heating, pre-heated combustion air or process ...

For many of our customers, efficient piping processes are critical to their operation and success. That’s why one of our leading services is providing piping solutions for all types of commercial/industrial needs. We can design, prefabricate, install, test, inspect and certify. Whatever you need, we can do. Contact us to find out more, or request a quote right ...

The G-Series gas turbine technology is based on the F-Series design with a wide range of incremental design enhancements, such as an improved compressor design, state-of-the-art combustor cooling, and advanced blade path seals among ...