Heat Exchanger Equipment & Supplies Near Afghanistan

After H2S removal the gas is fully saturated with water; the relative humidity (RH) is 100%. If water droplets should reach the cylinder heads and combustion chambers the water will destroy the oil film. This will lead to increased wear of moving parts as well as substantial reduction of the lifetime of the engine oil. Therefore, it is necessary to dry the gas to avoid condensation in the pipe ...

More than 1000 KAHL belt units are in operation worldwide and work in different sectors. Before you decide on a belt drier, you have the opportunity to perform a belt drier simulation for your project in our pilot ...

Des Champs heat exchangers offer designs utilizing plate counterflow heat exchangers, heat pipe, and energy recovery wheels. These heat exchangers form the backbone of many system configurations and can be configured with unique traversing frost prevention. ...

The Thermo-Z plate style heat exchanger is designed to recover heat from energy consuming processes up to 1500°F. Energy can be recovered and returned as process make-up air, used to preheat combustion air, or used for plant or office heating. Thermo-Z offers fully adjustable plate thickness and spacing as well as multiple ...

Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The ...

Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The ...

Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The ...

The counterflow configuration, four-pass design and optimized, secondary, tubular heat-exchanger result in efficiencies up to ...

The Thermo-T tubular heat-exchanger is designed to recover heat from energy-consuming processes up to 2000°F. Energy can be recovered and returned as process make-up air, used to preheat combustion air, or used for plant or office heating. Thermo-T offers fully adjustable tube-size and tube-spacing as well as both single-pass ...

VariMax IFRG combines Des Champs Products heat-exchanger design with indirect heating technologies to deliver contaminant-free process air with very high efficiency. Recirculation of the combustion gases allows the heater to attain an efficiency of 90%, 1,000°F (555°C) temperature rise, 1,200°F (649°C) discharge temperature, and ...

Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The ...

Superheated steam is not always desirable,for instance in those applications that heat transfer coefficient is important, saturated steam is preferred. Desuperheaters can reduce the temperature of steam or any other superheated vapor near to its saturated temperature by means of water or another coolant. Water is introduced into the process line and comes into direct contact with ...

Recuperator is basically a heat exchanger mounted in flue passage. ... If we heat the combustion air say up to 300 °C that much energy is saved. For every 100 ° C hot air 5% fuel saving can be ...

Bevel Washers are also known as “Conical Spring Washers” and specially designed for Heavy Duty Bolted Section such as Transformers, Rectifiers, Heat Exchangers, Transmission, etc. We are committed to provide high-quality washers with more accuracy to our ...

If the cold water supply is pressurized then hot water supply should be pressurized, for this application pressurized solar systems are proposed. INTER SOLAR DELUXE MODEL consists of collectors, pressurized dish end hot water tank with the heat exchanger, interconnecting piping and electrical backup, it heats the water indirectly. It is ...

With the special design of the PDS type furnaces, it is possible to do both, debinding and sintering in one furnace. For debinding, a special gas guiding configuration and molybdenum retort are utilized to protect the heating elements from all gaseous by-products. The heating elements and radiation shields are also constructed of molybdenum. The system is ...

TTE provides to customers with economical heat transfer solutions and equipment unparralled in performance, quality and ...

Capacity: 1 TPH – 15 TPH. Pressure: 10.54 kg/cm2g / 17.5 kg/cm2g / 21 kg/cm2g. Fuel(s): Wood/Wood ...

Capacity: 1 TPH – 15 TPH. Pressure: 10.54 kg/cm2g / 17.5 kg/cm2g / 21 kg/cm2g. Fuel(s): Rice ...

We have emerged as affluent manufacturer and supplier of Finned Tube Heat Exchanger. This is energy efficient and require less maintenance as compared to conventional heat exchangers. Our offered product is not only long lasting but has smooth finish. Using highest grade of raw materials sourced by our vendors, we manufacture and ...